Music Hall Turntables

Home Theater Used Gear About Policy Past Consignment Sales Testimonials Location

818-984-9651 *82 will display left of Phone Number - Disables Blocked Phone Numbers

818-984-9651  Calling From UnBlocked Smart Phones or VoIP Phones

Music Hall Landing Page

Music Hall Turntables:  

 
MMF 2.3 MMF 2.3LE MMF 2.3WH MMF 2.3SE
Music Hall 5.3LE - Ferrari red Turntable Music Hall 5.3SE - Rosewood Veneer Turntable
MMF 5.3 MMF 5.3LE MMF 5.3SE MMF 7.3
MMF 9.3 MMF 11.1 Ikura Ikura

MMF 7.3 - $1595.00 - unique dual-plinth construction originated by music hall.
Music Hall MMF 7.3 Turntable

The distinctive design of the mmf-7.3 isolates the critical sound reproducing components; platter, main bearing, tonearm, and cartridge on the top platform from the adjustable tip-toe feet which are mounted on the bottom platform. The motor speed controls, and wiring are isolated on their own platform and completely decoupled from the turntable.

Feature List:

  • music hall’s unique dual plinth construction
  • one-piece full carbon fiber tonearm
  • counterweight’s center of gravity is level with the stylus tip, is decoupled from the arm, and acts as a resonance damper
  • completely isolated/decoupled DC motor with 33⅓ and 45 rpm speed controls located in the front left corner of the turntable, thus canceling any potential vibration from the motor/belt to the cartridge
  • motor sits on its own resonance damping puck
  • Optional Ortofon 2M Bronze cartridge with a nude fine line stylus ($440 value)
  • the supplied cartridge is properly aligned and mounted
  • precision stainless steel main bearing sheathed in Teflon® for noise-free, fluid operation
  • non-resonant acrylic platter with metal screw-on record clamp and soft felt mat
  • high quality gold RCA connectors and detachable phono cable
  • adjustable tip toe feet with anti scratch cups
  • low noise fully manual belt drive design
  • built-in round spirit level for proper leveling
  • dust cover and 45rpm adaptor included
  • excellent instruction manual and easy assembly

Technical Specifications:

power supply    15V / 0-0.8mA DC
universal power supply
power connection    100 – 240 Volt 50 or 60 Hz
standby power consumption    < 1 W
speeds    33⅓ rpm & 45 rpm
electronic speed change
wow and flutter    ± 0.10 %
speed deviation    ± 0.06%
rumble max    > – 73 db
effective tonearm length    9 in. (230 mm)
tonearm weight    250 g (without counterweight)
effective tonearm mass    8.5 g
overhang    18 mm


MMF 9.3 - $2395.00 - unique Triple-plinth construction originated by music hall.
Music Hall MMF 9.3 Turntable
The distinctive design isolates the critical sound reproducing components: platter, main bearing, tonearm, and cartridge, on the top platform, from the adjustable tip-toe feet and wiring, which are mounted on the bottom platform. The motor and speed controls are isolated on their own vibration damping base and completely decoupled from the turntable.

feature list

  • music hall’s unique triple plinth construction
  • one-piece full carbon fiber tonearm
  • counterweight’s center of gravity is level with the stylus tip, is decoupled from the arm, and acts as a resonance damper
  • completely isolated/decoupled DC motor with 33⅓ and 45 rpm speed controls located in the front left corner of the turntable, thus canceling any potential vibration from the motor/belt to the cartridge
  • motor sits on its own resonance damping puck
  • optional Goldring Eroica LX low-output moving-coil cartridge with Gyger II line contact stylus ($795 value)
  • the cartridge supplied is properly aligned and mounted
  • inverted ceramic main bearing for super quiet, fluid operation
  • non resonant, 1” thick acrylic platter
  • soft felt platter mat
  • high quality gold RCA connectors and detachable phono cable
  • adjustable tip toe feet with anti scratch cups
  • low noise fully manual belt drive design
  • built-in round spirit level for proper leveling
  • dust cover and 45 rpm adaptor included
  • excellent instruction manual and easy assembly

technical specifications:

power supply    15V / 0-0.8mA DC
universal power supply
power connection    100 – 240 Volt
50 or 60 Hz
standby power consumption    < 1 W
speeds    33 ⅓ & 45 rpm electronic speed change
wow and flutter    ± 0.10 %
speed deviation    ± 0.06%
rumble max    > – 73 db
effective tonearm length    9 in. (230 mm)
tonearm weight    250 g (without counterweight)
effective tonearm mass    8.5 g
overhang    18 mm

 

product specifications:

w18.25 x d13.25 x h7.25 in.
40 lbs. pkg.


MMF 11.1 - $4495.00 featuring the unique quadruple-plinth construction originated by music hall

The distinctive design isolates the critical sound reproducing components, each on their own plinth. The tonearm is mounted to the upper plinth and the inverted ceramic main bearing is mounted to the second plinth allowing the partially sunken 1 1/2″ acrylic platter to spin freely.

Moving the main bearing to the second plinth improved cartridge tracking and significantly lowered background noise. The adjustable magnetic-levitation isolation feet, microprocessor speed control, motors, flywheel, and wiring are all mounted to the bottom plinth. The motors, flywheel, and speed control are further isolated on their own vibration damped dual-plinth platform, which is separately isolated from the upper three main plinths.

Sorbothane hemispheres separate each of the three main plinths and provide additional vibration damping. The bottom plinth functions as a mass-loaded resonant sink for the entire turntable. Two motors and a flywheel are used to increase torque and speed stability. The mmf-11.1 comes in a high-gloss piano black lacquer finish and ships without cartridge. A large encapsulating acrylic dustcover is included.

Feature List:

  • music hall’s unique quadruple-plinth design w/sorbothane vibration isolation
  • one-piece Project ‘9cc Evolution’ carbon fiber tonearm
  • the arm uses four hardened Swiss ABEC 7 ball races in an inverted bearing design
  • tonearm is internally wired with flexible wire drawn from high purity copper with only two contact points from cartridge to output connectors
  • counterweight’s center of gravity is level with the stylus tip is decoupled from the arm and acts as a resonance damper
  • fully adjustable azimuth, VTA, and dampened arm lift
  • exclusive microprocessor electronic speed controlled dual motor single flywheel drive system
  • 33 1/3 and 45 rpm speed change at the touch of button
  • motors and flywheel assembly are isolated on mass loaded resonant sink connected to the lower plinth
  • the dual motor flywheel system sits on the left side of the turntable thus eliminating all motor and belt vibration from the cartridge
  • magnetic-levitation adjustable isolation feet
  • inverted ceramic main bearing for super quiet fluid operation
  • thick acrylic platter
  • removable acrylic dustcover
  • high quality, gold RCA connectors with detachable phono cable
  • low noise fully manual belt-drive design, dustcover, 45rpm adaptor
  • ships securely in a substantial wood box
  • excellent instruction manual and easy assembly

Technical specifications:

speed of turntable:    33 1/3 or 45 r.p.m.
change speed    electronically, luminous buttons
deviation speed    < ±0.1%
variance speed    < ±0.08%
mechanical distance    > -45dB
electrical distance    > -65dB
drive    silicone belt over pulley
motor    2 x synchronous motors; the motor is controlled via microprocessor
platter    acrylic (11.8 in., 300 mm) weight – (7.4lbs., 3.35 kg)
power    switching power supply (90 – 246 VAC, 47-63Hz) type EU, UK,USA
electric input    23W DC
effective arm length    9in. (230 mm)
effective arm mass    8.5 g
mounting distance    8.3 in (212 mm)
overlap    .71 in (18 mm)
angle crank    24°
course zero error angle    ø 130.5, ø 243.7
force on the tip    0-3 g
plinth material    MDF
belt material    silicone rubber

product specifications
w21.3 x d13.8 x h7.8 in
39.5 lbs. pkg.


Ikura  - $1195.00 ikura represents a distinct visual and technical design departure for music hall. 

music hall collaborated with an outside industrial design firm to develop and complete the project. The foundation of ikura’s design remains the unique two-piece split-plinth design originated by music hall and the final product is the result of a dynamic design partnership between Doing & Done, headed by designer James Kyroudis, and music hall.


The mdf (medium density fiberboard) platter and felt mat sit on a high quality, stainless steel ball bearing sheathed in Teflon providing fluid and noise-free operation. The bearing assembly comes pre-charged with lubricant.


The effective length of the tonearm is nine inches. This allows for a very shallow tracking arc on the record thus reducing distortion and record wear. The tonearm comes mounted with a high quality moving magnet cartridge and features Swiss made ABEC 7 stainless steel bearings.
Each element of the ikura was carefully selected to provide you with the highest level of performance and sound quality. Used properly, the ikura will provide you with years of musical enjoyment.

Feature List:

  • music hall’s unique split-plinth design

  • gorgeous high gloss white or black finish

  • top tier one piece alloy tonearm

  • flexible internal tonearm wire drawn from high purity copper

  • counterweight’s center of gravity is level with the stylus tip

  • resonance damping counterweight is decoupled from the tonearm
  • two-speed stepped motor pulley for 33⅓ and 45 rpm
  • separately isolated dc synchronous motor
  • ortofon 2m blue moving magnet cartridge with user replaceable nude elliptical diamond stylus (a $225 value)
  • the cartridge supplied is properly aligned and mounted
  • precision stainless steel main bearing sheathed in teflon

  • main bearing provides noise free fluid operation

  • dynamically balanced MDF platter

  • soft felt mat

  • high quality gold RCA connectors with detachable phono cable
  • special vibration damping adjustable feet
  • low noise fully manual belt drive design
  • excellent instruction manual
  • quick and easy to assemble
  • dust cover and 45 rpm adaptor
  • not compatible with music hall cruise control


technical specifications:

power supply    115V/60Hz or 230V/50Hz
power absorption    2VA
motor    dc synchronous
speeds    33⅓ rpm
(manual change
to 45 rpm)
speed deviation    ± 0.9%
wow and flutter    ±0.15%
rumble max    > -70 db
mounting distance arm base    212mm
armtube material    aluminum
effective tonearm length    9 in (228.6mm)
effective tonearm mass    11g
overhang    0.7 in (18mm)
cartridge weights    2.0 – 16.0g
tonearm weight w/o counterweight    250g
platter diameter    11.81 in (30cm)
platter weight    2 lbs (.90kg)


product dimensions:


w18.25 x d13.25 x h5.5 in
20lbs. pkg.



Copyright: Kaplan Design